« back to Support Center

How To Remove Your Sistaco Colour

Our Express Remover has been carefully formulated to safely and easily remove your nail colour. When used correctly, there will be no damage to your natural nail. However, if you don’t have our Express Remover you can remove your colour with 100% acetone.

Rapid Remover Method
Express Remover Method
Rapid Removal Hub Method
100% Acetone Method
Sustainable Nails

How to Remove Using The Rapid Remover

Important: Leave on for at least 5-8 minutes

STEP 1

Begin by gently buffing away your Top Coat.

STEP 2

Apply a slightly thickened layer of The Rapid Remover onto the nail shade.

STEP 3

The Rapid Remover coat should loosen the nail shade and allow you to gently push it away.

STEP 4

Wash nails thoroughly and apply The Nail Elixir for continued nail health.

How to Use The Rapid Remover (Advanced Method)

STEP 1

Begin as usual by gently buffing away your Top Coat your nail colour should look mattified.

STEP 2

Apply a thickened layer of The Rapid Remover onto the nail shade. Let sit for at least 1 minute or until dry to touch.

STEP 3

With a bag and bowl of warm water, insert your hands into the bag, curling your fingers and let sit in the warm water for 2-3 minutes and remove. Ensure your hands are dry.

STEP 4

The Rapid Remover will have bonded with your nail colour allowing you to gently slide an orange stick under the colour. Start in the corner of your nail, slowly and gently pushing the layer of colour upwards.

STEP 5

Correctly applied, you should be able to gently lift the entire nail colour off your nail. Repeat for the rest of your nails. Use the orange stick to lift the colour for any stubborn spots.

STEP 6

Wash your hands thoroughly with soap and dry. Apply the Sistaco Nail Elixir to improve your nail health and growth.

How to remove using Rapid Removal Hub

Our Holographic and Metallic powders are applied differently than the classic range. If you want a longer application, follow the instructions for “Step 2 For Long Wear”. If you like to change your holographic or metallic colours frequently, follow the ‘Step 2 For Short Wear’ instructions.

Step 1

Turn lid in an anti clockwise direction to remove.

Step 2

Pour 5-40ml of 100% Acetone into the plastic insert provided and place into the ‘well’ of the hub. Replace the lid; fixing into position.

Step 3

Using a nail file, gently file the top coat to break surface.

Step 4

Turn on using the middle lower ON button. Small square lights will begin to flash, whilst your Rapid Remover heats. Once heated and ready for use the ‘Steam’ button will light up and you will hear a single beep. You can now insert your fingers into the top of the system as shown and grip the top slightly to allow the steam to better reach your nails. Be careful not to place fingers too low to avoid burning.

Step 5

When the red indicator END light turns on, the steam process is completed by two beeps. Remove your fingers and gently push off your application using the Sistaco 3-in-1 nail tool. Do this immediately otherwise your nail application could harden again. If this happens you will need to repeat Step 4 again. After finishing wash your nails and moisturise.

How To Remove Using 100% Acetone

Step 1

Gently buff the surface of your colour to penetrate the top coat.

Step 2

Saturate a cotton ball with 100% acetone. Hold to nail for 60 seconds.

Step 3

Repeat step 2 if required. Wipe away residue. Now decide what colour to put on next!

How To Remove Sustainable Nails

Step 1

Soak nails in warm soapy water for few minutes.

Step 2

Use orange stick to gently remove from natural nail.

Step 3

Use orange stick to gently remove any 'Nail Tab' residue on natural nail. (Use acetone if required)

How To Remove Using The Express Remover

Sistaco has over 100 shades in our powder collection and we’re not just all about the glitter and sparkle! We have all kinds of classic colours that never go out of style! Our powder collection ranges from muted beige tones to bright, warm shades.

Step 1

Gently buff the surface of your colour to remove the top coat.

Step 2

Apply the Express Remover taking care to avoid the skin.

Step 3

Wait 2 to 3 minutes or until the colour stops bubbling.

Step 4

Use a remover tool to gently push off the colour. Wipe away residue.

Step 5

Take your time. Repeat steps 2 - 3 if required.

Join Our Facebook Group

The private Sistaco Facebook Group has thousands of customers posting daily. Our helpful community is always happy to share suggestions and answer any questions you may have
TIP: you can also search within the group for a question to see if it’s been answered already!

Join The Facebook Group